View LB11824M_296215.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

Ordering number : ENN7107
Monolithic Digital IC
LB11824M
Direct PWM Drive Brushless Motor Predriver for On-Demand Water Heater and Air Conditioner Motors
Overview
The LB11824M is a direct PWM drive predriver IC for use with three-phase power brushless motors. The LB11824M can implement a motor drive circuit with the desired output capacity (voltage and current) by using appropriate external transistors. This device is optimal for motor drive in larger home appliances such as air conditioners and on-demand hot water heaters.
Package Dimensions
unit: mm 3073C-MFP30SD
[LB11824M]
15.2
30
16
Functions and Features
Three-phase bipolar drive Direct PWM drive Built-in forward/reverse switching circuit Full complement of built-in protection circuits, including current limiter, undervoltage protection circuit, motor lockup protection circuit, and thermal protection circuit. * Can be controlled by either a command voltage or the duty of an input PWM signal. * Provides three types of Hall-effect element signal pulse outputs. * * * *
1
(0.6) 1.0 0.4
10.5
7.9
15
2.45max
0.25
0.1 (2.25)
SANYO: MFP30SD
Specifications
Absolute Maximum Ratings at Ta = 25C
Parameter Supply voltage 1 Supply voltage 2 Supply voltage 3 Output current RF pin applied voltage LVS pin applied voltage TOC pin applied voltage VCTL pin applied voltage Symbol VCC1 max VCC2 max VCC3 max IO max VRF max VLVS max VTOC max VCTL max VCC1 pin VCC2 pin VCC3 pin Pins UL, VL, WL, UH, VH, WH Conditions Ratings 14.5 14.5 20 40 4 20 VCC2 14.5 Unit V V V mA V V V V
Continued on next page.
Any and all SANYO products described or contained herein do not have specifications that can handle applications that require extremely high levels of reliability, such as life-support systems, aircraft's control systems, or other applications whose failure can be reasonably expected to result in serious physical and/or material damage. Consult with your SANYO representative nearest you before using any SANYO products described or contained herein in such applications. SANYO assumes no responsibility for equipment failures that result from using products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other parameters) listed in products specifications of any and all SANYO products described or contained herein.
SANYO Electric Co.,Ltd. Semiconductor Company
TOKYO OFFICE Tokyo Bldg., 1-10, 1 Chome, Ueno, Taito-ku, TOKYO, 110-8534 JAPAN
80102RM (OT) No. 7107-1/17
0.65
LB11824M
Continued from preceding page.
Parameter Allowable power dissipation Operating temperature Storage temperature Symbol Pd max Topr Tstg Independent IC Conditions Ratings 0.9 -20 to +100 -55 to +150 Unit W C C
Allowable Operating Range at Ta = 25C
Parameter Supply voltage range 1-1 Supply voltage range 1-2 Supply voltage range 2 Supply voltage range 3 Output curent 12V constant-voltage output current 5V constant-voltage output current HP pin applied voltage HP pin output current Symbol VCC1-1 VCC1-2 VCC2 VCC3 IO I12REG IREG VHP IHP VCC1 pin VCC1 pin, with VCC1-VREG short-circuited VCC2 pin VCC3 pin Pins UL, VL, WL, UH, VH, WH Conditions Ratings 8 to 13.5 4.5 to 5.5 4.5 to VCC1 13.5 to 19 30 -50 -20 0 to 13.5 0 to 10 Unit V V V V mA mA mA V mA
Electrical Characteristics at Ta = 25C, VCC1 = 12 V, VCC2 = VREG
Parameter Supply current 1 Supply current 2 Output block Output voltage 1-1 Output voltage 1-2 Output voltage 2 Temperature coefficient 1-1 Temperature coefficient 1-2 Temperature coefficient 2 12 V Regulator-voltage output (12REG pin) Output voltage Voltage regulation Load regulation Temperature coefficient 5 V Regulator-voltage output (VREG pin) Output voltage Voltage regulation Load regulation Temperature coefficient VREG VREG1 VREG2 VREG3 VCC1 = 8 to 13.5 V IO = -5 to -20 mA Design target value* 4.7 5.0 40 5 0 5.3 100 30 V mV mV mV/C V12REG VCC3 = 15 V, IO = -30 mA 11.7 12.1 150 100 2 12.6 300 200 V mV mV mV/C 12VREG1 VCC3 = 13.5 to 19 V, IO = -30 mA 12VREG2 IO = -5 to -45 mA, VCC3 = 15 V 12VREG3 Design target value* VOUT1-1 VOUT1-2 VOUT2 Low level IO = 400 A Low level IO = 10 mA High level IO = -20 mA VCC1 - 1.1 0.1 0.8 VCC1 - 0.9 0.2 -1.5 1.5 0.3 1.1 V V V mV/C mV/C mV/C Symbol ICC1-1 ICC1-2 Stop mode Conditions Ratings min typ 15 2.5 max 20 4 Unit mA mA
VOUT1-1 Design target value*, Low level IO = 400 A VOUT1-2 Design target value*, Low level IO = 10 mA VOUT2 Design target value*, High level IO = -20 mA
Note*: These items are design target values and are not tested.
Continued on next page.
No. 7107-2/17
LB11824M
Continued from preceding page.
Parameter Hall Amplifier Block Input bias current Common-mode input voltage range 1 Common-mode input voltage range 2 Hall input sensitivity Hysteresis width Input voltage L H Input voltage H L VCTL pin Input voltage 1 Input voltage 2 Input bias current 1 Input bias current 2 PWM oscillator (PWM pin) Output H level voltage Output L level voltage External C charge current Oscillator frequency Amplitude TOC pin Input voltage 1 Input voltage 2 Input voltage 1L Input voltage 2L Input voltage 1H Input voltage 2H HP pin Output saturation voltage Output leakage current CSD oscillator (CSD pin) Output H level voltage Output L level voltage External C charge current External C discharge current Oscillator frequency Amplitude Current limiter circuit (RF pin) Limiter voltage VRF 0.45 0.5 0.55 V VOH (CSD) VOL (CSD) ICHG1 ICHG2 f (CSD) V (CSD) C = 0.01 F 2.2 3.2 0.9 -14 7 3.6 1.1 -10 11 200 2.5 2.75 4.0 1.3 -6 15 V V A A Hz Vp-p VHPL IHP leak IO = 7 mA VO = 13.5 V 0.15 0.5 10 V A VTOC1 VTOC2 VTOC1L VTOC2L VTOC1H VTOC2H Output duty 0% Output duty 100% Design target value*, 0% with VCC2 = 4.7 V Design target value*, 100% with VCC2 = 4.7 V Design target value*, 0% with VCC2 = 5.3 V Design target value*, 100% with VCC2 = 5.3 V 2.72 0.99 2.72 0.99 3.08 1.11 3.0 1.2 2.80 1.08 3.20 1.22 3.30 1.34 2.90 1.17 3.30 1.34 V V V V V V VOH (PWM) VOL (PWM) ICHG f (PWM) V (PWM) VPWM = 2.1 V C = 1000pF 2.75 1.0 -60 17.6 1.6 3.0 1.2 -45 22 1.8 3.25 1.3 -30 26.8 2.1 V V A kHz Vp-p VCTL1 VCTL2 Output duty 0% Output duty 100% 1.05 3.0 -80 1.4 3.5 -60 60 80 1.75 4.1 V V A A VIN (HA) VSLH (HA) VSHL (HA) IHB (HA) VICM1 VICM2 Hall device used For input one-side bias (Hall IC application) -2 0.5 0 50 20 5 -25 30 15 -15 50 25 -5 -0.5 VCC1 - 2.0 VCC1 A V V mVp-p mV mV mV Symbol Conditions Ratings min typ max Unit
IB1 (CTL) VCTL = 0 V IB2 (CTL) VCTL = 5 V
Note*: These items are design target values and are not tested.
Continued on next page.
No. 7107-3/17
LB11824M
Continued from preceding page.
Parameter Low-voltage protection circuit (LVS pin) Operating voltage Release voltage Hysteresis width VSDL VSDH VSD TSD TSD f (PI) VIH (PI) VIL (PI) VIO (PI) VIS (PI) IIH (PI) IIL (PI) VIH (SS) VIL (SS) VIO (SS) VIS (SS) IIH (SS) IIL (SS) VIH (FR) VIL (FR) VIO (FR) VIS (FR) IIH (FR) IIL (FR) VIH (N1) VIL (N1) VIO (N1) VIS (N1) IIH (N1) IIL (N1) VIH (N2) VIL (N2) VIO (N2) IIH (N2) IIL (N2) VN2 = VREG VN2 = 0 V VN1 = VREG VN1 = 0 V VF/R = VREG VF/R = 0 V VS/S = VREG VS/S = 0 V VPWMIN = VREG VPWMIN = 0 V 2.0 0 VREG - 0.5 0.2 -10 -130 0.3 0 -96 Design target value* (junction temperature) Design target value* (junction temperature) 3.6 4.1 0.35 3.8 4.3 0.5 4.0 4.5 0.65 V V V Symbol Conditions Ratings min typ max Unit
Thermal shutdown operation (Overheat protection circuit) Thermal shutdown operating temperature Hysteresis width PWMIN pin Input frequency H level input voltage L level input voltage Input open voltage Hysteresis width H level input current L level input current S/S pin H level input voltage L level input voltage Input open voltage Hysteresis width H level input current L level input current F/R pin H level input voltage L level input voltage Input open voltage Hysteresis width H level input current L level input current N1 pin H level input voltage L level input voltage Input open voltage Hysteresis width H level input current L level input current N2 pin H level input voltage L level input voltage Input open voltage H level input current L level input current 2.0 0 VREG - 0.5 -10 -130 0 -96 VREG 1.0 VREG 10 V V V A A 2.0 0 VREG - 0.5 0.2 -10 -130 0.3 0 -96 VREG 1.0 VREG 0.4 10 V V V V A A 2.0 0 VREG - 0.5 0.2 -10 -130 0.3 0 -96 VREG 1.0 VREG 0.4 10 V V V V A A 2.0 0 VREG - 0.5 0.2 -10 -130 0.3 0 -96 VREG 1.0 VREG 0.4 10 V V V V A A 50 VREG 1.0 VREG 0.4 10 kHz V V V V A A 125 20 145 25 165 30 C C
Note*: These items are design target values and are not tested.
No. 7107-4/17
LB11824M
Pd max - Ta
1.0 0.9W Independent IC
Power dissipation, Pd max - W
0.8 0.6 0.4 0.36W 0.2
-20
0
20
40
60
80
100
120
Ambient temperature, Ta - C
Three-Phase logic Truth Table (IN = [H] indicates a condition in which IN+ > IN-.)
F/R = L IN1 1 2 3 4 5 6 H H H L L L IN2 L L H H H L IN3 H L L L H H IN1 L L L H H H F/R = H IN2 H H L L L H IN3 L H H H L L Output PWM VH WH WH UH UH VH -- UL UL VL VL WL WL
S/S pin
Input condition H or open L Condition Stop Start
PWMIN pin
Input condition H or open L Condition Output OFF Output ON
N1,N2 pin
Input condition Pin N1 L L H or open H or open Pin N2 L H or open L H or open HP output 1/2 division 1 Hall Synthesis of three Halls
When S/S and PWMIN pins are not used, set the input to the L level voltage. For HP output, pulsed output of Hall input IN1 (1-Hall output), 1/2 division output of 1 Hall, or synthetic output of three phases of Hall input (three-Hall synthetic output) may be selected.
No. 7107-5/17
LB11824M Pin Assignment
GND 30 N2 29 N1 28 HP 27 F/R 26 PWMIN S/S 25 24 CSD 23 VCTL 22 PWM 21 TOC 12REG VCC3 20 19 18 LVS 17 VCC2 16
LB11824M
1 RF 2 WH 3 WL 4 VH 5 VL 6 UH 7 UL 8 VCC1 9 IN1+ 10 IN1- 11 IN2+ 12 IN2- 13 IN3+ 14 IN3- 15 VREG
Pin Description
Pin No. Symbol Pin Description Equivalent circuit
VREG
Output current detection 1 RF Connect a resistor(Rf) between this pin and ground. Set with the maximum output current IOUT = 0.5/Rf.
5k
1
VCC1
2 4 6 3 5 7 WH VH UH WL VL UL Output pin (external TR drive output) Duty control made on UH, VH, and WH sides.
2 3
4 5
6 7
8
VCC1
Power supply (output and Hall input blocks). Normally used with the 12 V power supply. Connect to VCC2 and VREG for application with the 5 V single power supply. Connect a capacitor between this pin and GND for stabilization.
VCC1
9 10 11 12 13 14 IN1+ IN1- IN2+ IN2- IN3+ IN3- Hall amplifier input. IN+ > IN- is the input high state, and the reverse is the input low state. Connect a capacitor between the IN+ and IN- inputs if there is noise in the Hall sensor signals.
300 9 11 13
300 10 12 14
Continued on next page. No. 7107-6/17
LB11824M
Continued from preceding page.
Pin No. Symbol Pin Description Equivalent circuit
VCC1
Regulated-voltage output pin (5V output) 15 VREG Connect a capacitor (about 0.1F) between this pin and ground for stabilization.
15
16
VCC2
Power pin (PWM oscillation, PWM comparator, VCTL amp). Normally connect to VREG.
VCC1
17
LVS
Voltage detection pin for low-voltage protection. To detect the supply voltage of 5 V or more, connect the zenor diode in series to set the detection voltage.
43k
17
18k
18
Power pin (VCC3) for use during application with the supply voltage of 12 V or more. 12 V is generated at the 12 REG pin. To use the 12REG pin, connect this pin to VCC1. When not used, keep both VCC3 and 12 REG open or connect them to GND.
18 19
VCC3 12REG
19
VCC2
20
20 TOC PWM waveform comparator pin. Normally used in the open condition. By inputting the voltage directly into this pin, the output duty can be controlled without using the VCTL amp.
20k
Continued on next page.
No. 7107-7/17
LB11824M
Continued from preceding page.
Pin No. Symbol Pin Description Equivalent circuit
VCC2
21
PWM
Pin to set the PWM oscillation frequency. Connect a capacitor between this pin and GND.
200 2k
21
34k VCC2
22
VCTL
Control voltage input pin. For control with this pin, set the PWMIN pin to the L level.
2.26V
40k
22
VREG
Pin to set the operation time of motor lock protection circuit and to set the initial reset pulse. 23 CSD Connect a capacitor between this pin and GND. When the protection circuit is not to be used, connect a capacitor and resistor (150kW, 4700pF) in parallel between this pin and GND.
300
23
VREG
50k
24 S/S Start/stop control pin. Start with L and stop with H or in the open condition
3.5k
24
VREG
50k
25 PWM IN PWM pulse input pin. Output drive with L and output OFF with H or in the open condition. For control with this pin, apply the voltage of VCTL2 voltage or more to the VCTL pin.
3.5k
25
Continued on next page.
No. 7107-8/17
LB11824M
Continued from preceding page.
Pin No. Symbol Pin Description Equivalent circuit
VREG
50k
26 F/R Forward/reverse input pin
3.5k
26
VREG
27
27 HP Hall signal output signal
VREG
50k
28 N1 Pin to select Hall signal output (HP output)
3.5k
28
VREG
50k
29 N2 Pin to select Hall signal output (HP output)
3.5k
29
30
GND
GND pin
No. 7107-9/17
LB11824M Hall-Effect Sensor Input/Output Timing Chart
F/R = L IN1 IN2
IN3 UH VH WH UL VL WL F/R = H IN1 IN2
IN3 UH VH WH UL VL WL
PWM output
No. 7107-10/17
5V
VCC3 12VREG LVS VCC2 LVSD VREG VREG VCC1 VM
VREG 12VREG
HP
TOC
VCTL
-
+ COMP PRI TSD LOGIC HP LOGIC HALL LOGIC DRIVER UH UL VH VL WH WL CURR N1 N2 HYS HALL AMP LIM RF
LB11824M
Sample Application Circuit (1) Bipolar transistor drive (upper side PWM) using a 5 V power supply
PWM
PWM OSC
VREF
S/S
SD
PWM IN
OSC
F/R
S/S N1 N2 VCC1 H
PWMIN
CSD
F/R
IN1+ IN1- IN2+ IN2- IN3+
IN3-
GND
H
H
No. 7107-11/17
VREG 12VREG LVS VCC2 LVSD VREG VREG 12VREG 12V VM
VCC3
HP
TOC
VREG VCC1
VCTL
-
+ COMP PRI TSD LOGIC DRIVER HP LOGIC HALL LOGIC UH VL VH WL WH CURR N1 N2 HALL HYS AMP LIM RF UL
LB11824M
(2) MOS transistor drive (lower side PWM) using a 12 V power supply
PWM
PWM OSC
VREF
S/S
SD
PWM IN
OSC
F/R
S/S VCC1 H
PWMIN N2
CSD
F/R
N1
IN1+ IN1- IN2+ IN2- IN3+
IN3-
GND
H
H
Pulse input
No. 7107-12/17
15V
VREG 12VREG LVS VCC2 LVSD VREG VREG 12VREG
VCC3 VM
HP
TOC
VCTL VCC1
-
+ COMP PRI TSD LOGIC HP LOGIC HALL LOGIC DRIVER UL UH VL VH WL WH CURR N1 N2 HALL HYS AMP LIM RF
LB11824M
PWM
PWM OSC
VREF
(3) NMOS transistor plus pnp transistor drive (lower side PWM) using a 15 V power supply
S/S
SD
PWM IN
OSC
F/R
S/S VCC1
PWMIN N2
CSD
F/R
N1
IN1+ IN1- IN2+ IN2- IN3+
IN3-
GND
No. 7107-13/17
LB11824M LB11824M Function Description 1. Output drive circuit This IC employs a direct PWM drive method to minimize the power loss at output. The output TR is normally saturated in the ON condition, adjusting the motor drive power by changing the output on-duty. Output PWM switching is made on UH, VH, and WH output sides. Since UL - WL and UH- WH outputs are of the same output form, either lower PWM or upper PWM can be selected by changing the external output Tr connection method. Selection of diode to be connected to the non-PWM side output requires attention because there is a problem of reverse recovery time. (Unless a diode with the short reverse recovery time is selected, the through current flows in an instant when the PWM side Tr is turned ON.) UL - WL and UH - WH outputs enter the high impedance condition at a time of stop or when the supply voltage is extremely low (below the allowable operation voltage). Accordingly, an appropriate measure (pull-down resistor, etc.) is necessary in the external circuit to prevent an incorrect action due to the leak current. 2. Current limiting circuit The current limiting circuit performs limiting with the current determined from I = VRF/Rf (VRF = 0.5Vtyp, Rf: current detector resistance) (that is, this circuit limits the peak current). Limiting operation includes decrease in the output on-duty to suppress the current. The current limiting circuit incorporates a filter circuit to prevent an incorrect action of current limiting operation due to detection of the reverse recovery current of output diode during PWM To pin RF Current detection resistance operation. This internal filter circuit will be enough to prevent trouble for normal application. In case of an incorrect action (diode reverse recovery current flowing for 1s or more), add an external filter circuit (R, C low pass filter, etc.). 3. Power save circuit This IC enters the power save condition to decrease the current dissipation in the stop mode. In this condition, the bias current of most of circuits is cut off. Even in the power save condition, the 5 V regulator output (VREG) is given. If the bias current of Hall device is to be cut, 5V and Hall device may be connected via PNP Tr as a means to meet such needs.
To pin VREG
To pin S/S
Hall device
4. Compatibility with various power supplies To operate this IC with external 5V power supply (4.5 - 5.5 V), short-circuit VCC1 and VREG pin for connection to power supply. To operate this IC with external 12 V power supply (8 - 13.5 V), connect power supply to VCC1 (5V is generated at the VREG pin to function as a power supply to the control circuit). To operate this IC with external 15 V power supply (13.5 - 19 V), connect power supply to VCC3 and short-circuit 12REG and VCC1 pins (12 V is generated at the 12REG pin to function as a power supply to VCC1). Connect the VCC2 pin basically to the VREG pin. In an application in which the motor rotation speed is to be determined by the external fixed voltage (resistor division, etc.), set VCC2 to 12 V (by connecting to VCC1) to suppress variation of the output duty. (Variation of IC is difficult to affect adversely because of increase in the PWM oscillation amplitude and in the comparator dynamic range.) 5. PWM frequency PWM frequency is determined from the capacity C (F) of capacitor connected to the PWM pin. fPWM . .1/(45000 x C) = Connection of a 1000 pF capacitor causes oscillation of about 22 kHz. Excessively low PWM frequency causes causes a switching sound from the motor while excessively high PWM frequency causes increase in the power loss at the output. About 15 - 50 kHz is recommended. Capacitor GND should be arranged near the IC GND pin as much as possible to protect from the effect of output noise.
No. 7107-14/17
LB11824M 6. Drive method The output duty can be controlled according to any of following methods. * Control with the VCTL pin voltage For the control voltage, refer to the electric characteristics. For control with the VCTL pin, set the PWMIN pin voltage to the L level. * Control with the voltage applied to the TOC pin The TOC pin voltage and PWM oscillation waveform are compared to determine the output duty. The output duty becomes 0 % when the TOC pin voltage exceeds VOH (PWM) (3.0 Vtyp) and 100% when it becomes lower than the VOL (PWM) (1.2 Vtyp). For control with the TOC pin, set the PWMIN pin voltage to the L level. For control with the input level other than the internal CTL amp control input level, external connection of amp allows setting to the arbitrary input level (with the external amp output connected to the TOC pin). For control from the TOC pin, fix the VCTL pin voltage. For an application in which the regulated voltage is applied to the TOC pin through resistor division, etc., it is necessary to take into account the effect of resistor (about 20 k) incorporated between the TOC pin and CTL amp output. (Variation about 20%, temperature characteristics about +0.3%/C). If the noise is included in the voltage to be applied to the TOC pin, chattering may occur in the output. In this case, stabilization with a capacitor is necessary. * Pulse control with the PWMIN pin The output can be controlled on the basis of duty obtained by entering the pulse in the PWMIN pin. The output can be turned ON when the L-level Pin PWMIN input voltage is applied to the PWM pin and OFF when the H-level input voltage is applied. With the PWMIN pin open, the output becomes the H level and is turned OFF. If input with reversed logic is necessary, addition of external Tr (NPN) may be enough. Pulse input For control with the PWMIN pin, set the VCTL pin voltage that is more than the VCTL2 voltage (output duty set to 100%) or connect the TOC pin to GND. 7. Hall input signal The Hall input requires the signal input with an amplitude exceeding the hysteresis width (50 mV max). Considering the effect of noise and phase displacement, the input with the amplitude of 120 mV or more is recommended. When the noise causes disturbance in the output waveform (at a time of phase change) or HP output (Hall signal threephase synthesis output), insert a capacitor to the input to prevent such trouble. The Hall input is used as a signal to determine the input to the restriction protection circuit and the protection circuit during reverse. Though noise is ignored to a certain degree, due attention must be paid when using these protection circuits. When all three phases of Hall input signal are entered, the output is turned OFF entirely (all of UL, VL, WL, UH, VH, and WH OFF). To enter the Hall IC output, fix one side of input (+ or -) to the voltage within the common-mode input range for Hall device. This will allow input from 0 to VCC1 for another single-side input. 8. Circuit for low-voltage protection This circuit detects the voltage applied to the LVS pin. When this voltage drops below the operation voltage (see the electric characteristics), the one-side output (UH, VH, and WH) is turned OFF. To prevent repetition of output ON/OFF near the protection activation voltage, the hysteresis is provided. Accordingly, the output is not recovered unless the voltage rises by about 0.5 V above the activation voltage. The protection activation voltage is for the 5V system detection level. The detection level can be raised by connecting the zenor diode in series to the LVS pin and by shifting the detection level. The LVS pin inrush current at a time of detection is about 65A. To detection power supply To stabilize rise of the zenor diode voltage, increase the diode current by inserting the resistor between the LVS pin and GND. To pin LVS When the protection circuit is not used, apply a voltage on a level where the protection is not activated, instead of setting the LVS pin open (output OFF with the pin open).
No. 7107-15/17
LB11824M 9. Motor lock protection circuit A motor lock protection circuit is incorporated for protection of IC and motor when the motor is locked. When the Hall input signal is not changed for a certain period with the motor driving, the one-side output (UH, VH, WH) is turned OFF. The time is set by means of a capacity of a capacitor connected to the CSD pin. Set time (s) .= 154 x C (F) . Addition of a 0.01 F capacitor causes a protection time of about 1.54 seconds. (Drive is turned OFF when one cycle of Hall input signal is longer than this time period.) The time to be set must have a sufficient allowance so that the protection is not activated at a normal motor startup. Select the capacitor of 4700 pF or more. The protection circuit is not activated when braking. To cancel the restriction protection condition, one of following steps must be taken: * Stop mode (10 s or more) * Maintaining the output duty 0% condition through input of VCTL or PWMIN for more than the period of tCSD x 2. (tCSD (s) .= 0.5 x C (F). When the 0.01 F capacitor is added, maintaining for about 10 ms or more is necessary.) . * Re-application of power supply The CSD pin acts also as an initial reset pulse generation pin and causes reset of the logic circuit when connected with GND. Accordingly, the motor drive condition can not be obtained. When this pin is not to be used, a resistor of about 150 k and a capacitor of about 4700 pF must be connected to GND in parallel. When the restriction protection circuit is not used, following functions are also invalid: * Protection circuit for the reverse mode * Overheat protection circuit 10. Overheat protection circuit One-side output (UH, VH,WH) is turned OFF when the junction temperature (Tj) exceeds a specified temperature (TSD). Since the minimum variation of TSD is 125C, thermal design must be made so that Tj = 125C is not exceeded except in the case of abnormality. Accordingly, Pdmax when Tj (max) = 125C is 0.72 W (Ta=25C) When the motor lock protection is not to be used by inserting in parallel the resistor of about 150k and capacitor of about 4700pF between the CSD pin and GND, this overheat protection circuit does not function. In this case, Tj (max) = 150C, so that Pdmax = 0.9W (Ta = 25C) 11. Forward/reverse rotation To select forward or reverse in the rotation condition, a measure is taken to prevent flow of the through current (through current due to the output Tr OFF delay time at selection) at the output. Selection during rotation causes the current exceeding the current limit value to flow through the output Tr because of the motor coil resistance and motor reverse electromotive voltage condition. It is therefore necessary to select the external output Tr that is not damaged by this current or to select forward/reverse only when the motor rotation speed has decreased to a certain level. 12. Power supply stabilization This IC is of a switching drive type and the power line tends to be affected. It is therefore necessary to connect a capacitor of sufficient capacity for stabilization between the VCC1 pin and GND. To insert a diode in the power line to prevent breakdown through reverse connection of power supply, the power line becomes more readily affected. It is necessary to select a larger capacity. To turn ON/OFF the power supply with a switch, etc., large distance between the switch and capacitor causes substantial deviation of the supply voltage due to the line inductance and inrush current into the capacitor. In certain cases, the withstand voltage may be exceeded. In this case, do not use a ceramic capacitor whose series impedance is low. Instead, use an electrolytic capacitor to suppress the inrush current and to prevent voltage rise. 13. VREG stabilization To stabilize the VREG voltage that is the power supply for the control circuit, connect a 0.1F or more capacitor between VREG and GND. The capacitor GND must be wired near the GND pin of IC as much as possible.
No. 7107-16/17
LB11824M
Specifications of any and all SANYO products described or contained herein stipulate the performance, characteristics, and functions of the described products in the independent state, and are not guarantees of the performance, characteristics, and functions of the described products as mounted in the customer's products or equipment. To verify symptoms and states that cannot be evaluated in an independent device, the customer should always evaluate and test devices mounted in the customer's products or equipment. SANYO Electric Co., Ltd. strives to supply high-quality high-reliability products. However, any and all semiconductor products fail with some probability. It is possible that these probabilistic failures could give rise to accidents or events that could endanger human lives, that could give rise to smoke or fire, or that could cause damage to other property. When designing equipment, adopt safety measures so that these kinds of accidents or events cannot occur. Such measures include but are not limited to protective circuits and error prevention circuits for safe design, redundant design, and structural design. In the event that any or all SANYO products (including technical data, services) described or contained herein are controlled under any of applicable local export control laws and regulations, such products must not be exported without obtaining the export license from the authorities concerned in accordance with the above law. No part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording, or any information storage or retrieval system, or otherwise, without the prior written permission of SANYO Electric Co., Ltd. Any and all information described or contained herein are subject to change without notice due to product/technology improvement, etc. When designing equipment, refer to the "Delivery Specification" for the SANYO product that you intend to use. Information (including circuit diagrams and circuit parameters) herein is for example only; it is not guaranteed for volume production. SANYO believes information herein is accurate and reliable, but no guarantees are made or implied regarding its use or any infringements of intellectual property rights or other rights of third parties.
This catalog provides information as of August, 2002. Specifications and information herein are subject to change without notice. PS No. 7107-17/17

▲Up To Search▲

Price & Availability of LB11824M

	To Download LB11824M Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .